AML M3000 User's Guide Page 131
- Page / 156
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
12Maintenance
12-3
Avoiding Damage
The M3000 can be damaged by any of the following conditions:
Electrical
The electronic components of the M3000 can be damaged by exposure to intense electrical fields.
If possible, avoid exposing the unit to the following conditions:
• Electrostatic discharge produced by friction. For example, heavily carpeted areas during
periods of low humidity.
• Avoid using the M3000 with a Modem during electrical storms.
• Avoid exposure to any source of intense arcing.
• Exposure to powerful electromagnetic fields. For example, large motors, induction coils,
transformers, etc.
• Exposure to sources of ionizing radiation. For example, x-rays, etc.
Mechanical
Avoid the following:
• Direct exposure to water. Do not immerse.
• Severe drops or physical impact.
• Extreme heat or open flame. For example, do not leave on the dash board or inclosed in a
vehicle.
• Highly corrosive environments
• Strong industrial cleaning solvents
Cleaning
When the unit needs cleaning, use only a soft cloth, dampened in clean warm water. Do not use
petroleum based solvents, or powerful detergents.
.
- User's Guide 1
- Contents 3
- Programming 5-1 4
- Setup Procedures 6-1 5
- Communications 7-1 8
- Advanced Operations 8-1 8
- M3000 Programmer 9-1 9
- Troubleshooting 10-1 9
- Specifications 11-1 9
- Maintenance 12-1 9
- Appendixes A-1 10
- Overview 11
- Portable Mode 12
- Non Portable Modes 12
- Communications 12
- Symbols: 13
- 1Installation 14
- Keyboard Wedge Installation 15
- Caution: 15
- Serial Wedge Installation 16
- RS-232 Serial Installation 16
- Modem Installation 18
- Installing Input Devices 18
- 2Keyboard 19
- Keyboard Layout 20
- Other Key Combinations 21
- 3Function Reference 22
- ATA FILES 23
- OOKUP FILES 24
- Search Text 26
- Startup - Portable Mode 28
- Using the INPUT Function 30
- Edit/Review a Data File 33
- Startup - Non Portable Mode 34
- Keyboard Wedge Mode 35
- Serial Wedge Mode 35
- RS-232 Serial Mode 36
- Nonportable Mode 37
- ➨RS232 SERIAL 37
- RS232 Serial 37
- Scanning Bar Codes 38
- CCD Scanning 41
- Slot Reader (Badge Reader) 42
- 5Programming 43
- Erasing a Program 44
- Exiting a Program 44
- Programming Tutorial 45
- EOF (End of File) Parameters 46
- Use Receive Data Files Only? 46
- Output Prefix 49
- Output Suffix 49
- Input Type 49
- Screen Positioning 50
- Input Size 50
- Input Controls 50
- Display Pattern 50
- Input Mask 50
- Input Definition # 5 52
- End of Program 53
- Stamp Commands 53
- ITEM NUMBER 54
- LOC (Location) 55
- UOM (Unit of Measure) 55
- DESCRIPTION 55
- *P6 (No Prompt) 55
- Creating a New Program 56
- SOF Text 57
- SOF Delay 57
- EOF Text 57
- EOF Delay 57
- Allow Append to End of File? 58
- Header Input? 58
- New Screen? 58
- Sample Prompt Text 59
- Enter Spaces Here 59
- Exhibit Text is not required 60
- Str Row 61
- Str Col 61
- End Row 61
- End Col 61
- Screen Specifications: 62
- Data Input Parameters 63
- Input Size Max 63
- Input Size Min 63
- Require Input? 63
- Auto Advance? 63
- Input Source K, B, S, or X 65
- Bar Code Types 65
- Bar Code Types is required 66
- Default Data is not required 66
- Prefix is 67
- Prefix is not required 68
- Prefix Delay is required 68
- Suffix is not required 68
- 6Setup Procedures 69
- Cursor Function 70
- Auto Advance 72
- ON/OFF* 72
- Setup Categories 75
- Keyboard Wedge 76
- Serial Wedge 76
- RS232 Serial 76
- Serial Port 78
- Bar Codes 81
- UPC/EAN Addons (SUPPLEMENTS) 83
- I 2 OF 5 83
- CODABAR 84
- CODE 128 84
- CODE 93 85
- MSI/Plessey 85
- Code 11 86
- Termination Character 86
- Preamble 87
- Postamble 87
- Bar Code Edit 87
- Bar Code Beeper 88
- Laser/CCD Opts (Options) 88
- Transmit Setup 89
- Num Lock 92
- SOT Text (Start of Transmit) 92
- SOT Delay 92
- EOT Text (End of Transmit) 92
- Other Setup 93
- Reset Setups 94
- 7Communications 95
- Communication Software 98
- FUNC + XMIT 99
- Transmit Select 99
- PCOM COMMUNICATION SOFTWARE 100
- SOFTCOM Kill Program 101
- Using SOFTCOM 102
- 8Advanced Operations 106
- Lookup Table Definition 107
- Simple Lookup File 107
- Lookup Tbl/File 108
- Lookup File Definition 109
- Lookup File with Display 109
- Creating the ASCII Data File 110
- Importing an ASCII Data File 113
- Other Advanced Options 114
- Input Source 115
- K,B,S or X: S 115
- Transmit Paused 115
- Press Any Key 115
- 9Troubleshooting 116
- Bar Code Data Errors 117
- Function Recall Errors 117
- Miscellaneous Errors 117
- Function Search Errors 119
- Serial Input Error Messages 119
- Troubleshooting Guide 120
- 10Specifications 121
- Battery Performance 122
- Input/Output Specifications 122
- 11Maintenance 126
- Dimple on This 127
- End of EPROM 127
- Avoiding Damage 128
- 12Maintenance 129
- Appendixes 132
- FUNCTION KEYS 133
- SPECIAL KEYS 133
- UPC VERSION A 137
- UPC-A BAR CODE 137
- UPC VERSION E 138
- 0123456789 139
- A123456B 141
- 0000123455555555558 142
- CHARACTER SET: 143
- CHARACTERISTICS 145
- CHARACTER SET 145
- 012345678 146
- APPENDIX L 151
- APPENDIX M 151
© 2020, manymanuals.com. All rights reserved. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals